Devices You Need to Install a New Bathtub
Devices You Need to Install a New Bathtub
Blog Article
Just how do you feel on the subject of Installing A Bathtub?
Setting up a tub isn't exactly rocket science, however it does require strong plumbing, woodworking, and also occasionally, tiling abilities. Changing an old bath tub with a brand-new one is additionally a reasonably difficult project. If the old tub is conveniently obtainable, the task can relocate easily; if you need to open a wall to remove the old tub and position the new bathtub, the job is a lot harder. In either instance, the task is within a residence handyman's abilities, although you will certainly require an assistant to vacate the old bathtub and also embeded in the brand-new one. Make certain you have actually qualified yourself for the job and are comfortable attempting it. Rather than hiring a service provider to take control of a halfway-completed job, it is much better to consider using one before you begin. Opportunities are you may need a specialist plumber to make tube links.
This short article will certainly aid you set up a new bath tub in your shower room if you have already acquired a new tub and also don't need to change the setup of your previous water system pipes.
Your devices as well as material list ought to comprise the following:
Preparing for the Setup
Firstly, the sustaining frame provided with the bath needs to be fitted (if required) according to the supplier's instructions. Next off, fit the faucets or mixer to the bathtub. When suitable the tap block, it is very important to make sure that if the faucet comes with a plastic washing machine, it is fitted between the bathroom and the faucets. On a plastic bath, it is additionally sensible to fit a supporting plate under the faucets unit to avoid strain on the bathtub.
Fit the adaptable tap adapters to the bottom of the two faucets using 2 nuts as well as olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet with the hole in the bath. Make use of the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Ensure you make use of all of the provided washers.
Link the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bathroom should now prepare to be fitted in its final setting.
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your installation, then the first thing you must do is separate the water supply. After doing so, switch on the faucets to drain pipes any type of water continuing to be in the system. The procedure of removing the existing taps can be rather troublesome because of the limited accessibility that is often the case.
Utilize a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipelines to the faucets. Have a fabric prepared for the staying water that will come from the pipes. Once the supply pipes have been removed, utilize the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single taps from turning during this process. When the taps have been eliminated, the holes in the bath/basin will certainly need to be cleaned up of any type of old securing substance.
Prior to carrying on to fit the brand-new faucets, contrast the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new taps to fit.
Setting up the Tub
Utilizing the two wooden boards under its feet, place the bathtub in the required position. The wooden boards are helpful in evenly spreading the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto 4 little points.
The following objective is to make sure that the tub is leveled all round. This can be accomplished by inspecting the spirit level and adjusting the feet on the bath tub till the level checks out level.
To install faucets, fit all-time low of the outermost versatile tap connector to the ideal supply pipeline by making a compression sign up with; then do the same for the other faucet.
Activate the water and also inspect all joints as well as new pipework for leaks and also tighten them if needed. Fill up the bathtub as well as additionally inspect the overflow outlet and also the typical outlet for leakages.
Lastly, deal with the bath paneling as defined in the producer's user's manual. Tiling as well as sealing around the tub should wait till the bathtub has been made use of a minimum of once as this will certainly resolve it into its last setting.
Fitting New Touches
If the tails of the new taps are plastic, after that you will require a plastic port to prevent damages to the thread. One end of the connector fits on the plastic tail of the faucet and the various other end supplies a connection to the current supply pipes.
If you require to fit a monobloc, after that you will call for decreasing couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin ensuring that the washing machines are in area between the faucet and the sink. Safeguard the tap in position with the producer given backnut. When the faucet is securely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal tap adapters. The former kind ought to be attached to the tap finishes first, tightening only by hand. The supply pipelines can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Bath tub
In the area where the bath fulfills the tile, it is needed to seal the joins with a silicone rubber caulking. This is necessary as the fitting can move sufficient to crack a stiff seal, creating the water to penetrate the wall surface in between the bath as well as the tiling, bring about problems with moisture and also possible leakages to the ceiling listed below.
You can choose from a range of coloured sealers to assimilate your fixtures as well as installations. They are sold in tubes and cartridges, as well as can sealing spaces approximately a size of 3mm (1/8 inch). If you have a larger space to load, you can load it with twists of soaked paper or soft rope. Bear in mind to constantly fill the tub with water prior to securing, to permit the movement experienced when the tub is in usage. The sealer can crack fairly early if you do not take into consideration this activity before sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise quickly offered on the marketplace. It is suggested to fit the floor tiles using water-resistant or waterproof glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you like more info about How to Install a Bathtub Yourself? Make a remark directly below. We will be glad to know your feelings about this posting. We are looking forward to see you back again in the future. Feel free to set aside a second to share this write-up if you enjoyed reading it. Bless you for your time. Don't hesitate to check our website back soon.
Find Out More
Report this page